X.25 is a packet-switching protocol for wide area network (WAN) connectivity that uses a public data network (PDN) that parallels the voice network of the Public Switched Telephone Network (PSTN).
What is X.25?
Apacket-switching protocolforwide area network (WAN)connectivity that uses a public data network (PDN) that parallels the voice network of thePublic Switched Telephone Network (PSTN). The current X.25 standard supports synchronous, full-duplex communication at speeds up to 2 Mbps over two pairs of wires, but most implementations are 64-Kbps connections via astandard DS0 link.
X.25 was developed by common carriers in the early 1970s and approved in 1976 by the CCITT, the precursor of theInternational Telecommunication Union (ITU), and was designed as a global standard for a packet-switching network. X.25 was originally designed to connect remote character-based terminals tomainframe hosts. The original X.25 standard operated only at 19.2 Kbps, but this was generally sufficient for character-based communication between mainframes and terminals.
Because X.25 was designed when analog telephone transmission over copper wire was the norm, X.25 packets have a relatively large overhead of error-correction information, resulting in comparatively low overall bandwidth. Newer WAN technologies such asframe relay, Integrated Services Digital Network (ISDN), andT-carrierservices are now generally preferred over X.25. However, X.25 networks still have applications in areas such as credit card verification, automatic teller machine transactions, and other dedicated business and financial uses.
How X.25 Works
The X.25 standard corresponds in functionality to the first three layers of the7 layers Open Systems Interconnection (OSI) reference modelfor networking. Specifically, X.25 defines the following:
- The physical layer interface for connectingdata terminal equipment (DTE), such as computers and terminals at the customer premises, with the data communications equipment (DCE), such as X.25 packet switches at the X.25 carrier’s facilities. The physical layer interface of X.25 is called X.21bis and was derived from theRS-232 interface for serial transmission.
- Thedata-link layer protocolcalled Link Access Procedure, Balanced (LAPB), which defines encapsulation (framing) and error-correction methods. LAPB also enables the DTE or the DCE to initiate or terminate a communication session or initiate data transfer. LAPB is derived from theHigh-level Data Link Control (HDLC) protocol.
- The network layer protocol called the Packet Layer Protocol (PLP), which defines how to address and deliver X.25 packets between end nodes and switches on an X.25 network usingpermanent virtual circuits (PVCs)or switched virtual circuits (SVCs). This layer is responsible for call setup and termination and for managing transfer of packets.
An X.25 network consists of a backbone of X.25 switches that are called packet switching exchanges (PSEs). These switches provide packet-switching services that connect DCEs at the local facilities of X.25 carriers. DTEs at customer premises connect to DCEs at X.25 carrier facilities by using a device called a packet assembler/disassembler (PAD). You can connect several DTEs to a single DCE by using the multiplexing methods inherent in the X.25 protocol. Similarly, a single X.25 end node can establish several virtual circuits simultaneously with remote nodes.
An end node (DTE) can initiate a communication session with another end node by dialing its X.121 address and establishing avirtual circuitthat can be either permanent or switched, depending on the level of service required. Packets are routed through the X.25 backbone network by using the ID number of the virtual circuit established for the particular communication session. This ID number is called the logical channel identifier (LCI) and is a 12-bit address that identifies the virtual circuit. Packets are generally up to 128 bytes in size, although maximum packet sizes range from 64 to 4096 bytes, depending on the system.
X.25 related Protocols
Related protocols include X.3, which defines the parameters for configuring a PAD; X.28, which defines the data transmission interface between the DTE and the PAD; and X.29, which defines a control protocol between the DTE and the PAD. TheRemote Access Service (RAS)for Microsoft Windows NT and theRouting and Remote Accessfeature of Microsoft Windows 2000 support X.25 PADs for dial-up clients and smart cards for direct connection to the X.25 network of remote access servers and clients.
X.25 not so efficient for interactive communication
X.25 is efficient for file transfer but not for interactive communication such as Telnet sessions, in whichTCP/IPis run over X.25. If you often use Telnet from your X.25 terminal, you can improve efficiency by employing VanJacobsen TCP/IP Header Compression to reduce the overhead of the TCP/IP packet header from 40 bytes to 5 bytes (if your TCP/IP stack supports this feature).
Another reason that X.25 is inefficient for interactive communication is the typical half-second latency in communication due to the store-and-forward nature of the packet-switching network. Frame relay does not use store-and-forwardpacket switchingand hence has much less latency.
X.25 Updates
The X.25 standard is updated every four years. Versions after 1984 are backward compatible with the 1984 version. However, if a network using the 1980 version of X.25 needs to communicate with a DTE on a network based on a later version, you must properly configure the routers connecting these networks.
